Recent Posts

Pages: 1 2 3 [4] 5 6 ... 10
31
General / Oil cooler air scoop?
« Last post by nate92754 on January 05, 2024, 07:25:18 am »
I've seen an oil cooler air scoop on various sites for sale. Is this more of a asphalt thing? Would it just scoop up dirt and mud and cause more problems running on dirt tracks?
32
General / Re: Happy New Year
« Last post by justfreaky on December 31, 2023, 04:55:26 pm »
Happy New Year Randy, Ryan and Robert!!!
Hoping 2024 brings you much success and happiness.

And Happy New Year to all the members here at LegendsRacer!

Steve
33
General / Happy New Year
« Last post by RPM on December 31, 2023, 03:04:05 pm »
From all of us here at RPM, we hope everyone had a Merry Christmas and A Happy New Year.

We hope everyone has a fun a successful 2024 in racing.

Randy - RPM
34
Engine Care & Tuning / Re: 1250 Motor Mount Issue
« Last post by Young Moses on November 08, 2023, 05:20:46 pm »
Thank you very much Randy for the insight! I will see what I find and get back to you. It's definitely split bad I just have to pinpoint the exact area the oil is coming from.
Thanks,
Josh
35
General / INEX approves Afco shocks
« Last post by justfreaky on November 06, 2023, 04:44:14 pm »
News from INEX
36
Engine Care & Tuning / Re: 1250 Motor Mount Issue
« Last post by RPM on October 30, 2023, 09:48:55 am »
Support the engine with a floor jack. Remove the bolts and the mount. Have a look down the hole to see if you can see any other cracks inside the bolt hole in the threaded area.

I have never come across an engine with both sides broken like that. There is no pressurized oil there, but there is a ton of oil sling from the rotating transmission.

Without slitting the cases, the only possible way I can see of trying to stop the oil is to try silicone. But that could be problematic if the case is cracked internally and the silicone hydraulics when installing the bolts.

You can remove the bottom half of the case without disassembling the complete engine. You would be able to get the crack(s) welded then and that will resolve the leak completely. If you do pull the bottom end off, you'll need a couple of gaskets and o-rings.

Let us know if we can be of any assistance.

Randy - RPM


37
Engine Care & Tuning / Re: 1250 Motor Mount Issue
« Last post by justfreaky on October 27, 2023, 07:18:37 pm »
Okay, understand a bit better know. I am going to guess that your case is cracked there. No good way to repair it.

Steve
38
Engine Care & Tuning / Re: 1250 Motor Mount Issue
« Last post by Young Moses on October 27, 2023, 04:59:37 pm »
Hey steve,
Thanks for the response. The oil is coming out of the vertical crack that the bolt is running into to hold the engine. Also that isn't JB weld it's the seam in the case where it splits open it seems to be the gasket you can see.

Josh
39
Engine Care & Tuning / Re: 1250 Motor Mount Issue
« Last post by justfreaky on October 27, 2023, 02:41:28 am »
Hi Josh,
 Took me a bit to sort out your pic, but the video is much clearer. Not sure why you have that piece of pipe on there (the split one). It needs to be replaced with the proper mounting parts.
Your leak is likely coming from that long crack around the block that has been JB Welded. Block up you engine and pull that motor mount off. I am sure you will see where it's leaking.

Steve
40
Engine Care & Tuning / Re: 1250 Motor Mount Issue
« Last post by Young Moses on October 26, 2023, 06:04:05 pm »
https://youtube.com/shorts/vH3EHh_bZlY?si=Ll002nlylL_1WyTN

This is the link to the video of the motor leaking. (File too large to upload on post).
Pages: 1 2 3 [4] 5 6 ... 10
anything